A bit of fill and antifoul will sort it out.

[Slacko]

Re: A bit of fill and antifoul will sort it out.

On the engine front I've got the battery cables in (the ones I had were 100mm too short).
I need to finalise the control cables operation and setup,
the electrical panel cables are just long enough, so are plug and play,
and I need to put a 10 micron filter in the full line.

I've listed the old engine online as components rather than as a unit, and have sold the Savage heat exchanger for 1/2 purchase price which was better than expected, and got $300 for the dead engine.
The gearbox, oil cooler and propeller are still listed so I hope to claw back a reasonable amount.

[Slacko]

Re: A bit of fill and antifoul will sort it out.

The fuel filter, control cables and earth strap for the prop shaft have all been ticked of the list now so the engine is ready to go once the exhaust pipe to the back is put back in.
It is out while I'm doing the rudder leak repair.
I'll build a new box around the engine once I'm back in the water.

The earth strap is sitting in place here, I had to put a slight twist on the arm so it sits flat on the shaft when screwed down.
IMG20230320200052.jpg
The wire is attached to one of the studs sticking up from the end of it.

The rudder repair is still in progress, as I will redo the attachment of the skeg to the hull between the rudder and the propeller.
Inside is going to get some beefing up too, either fiberglass or timber depending on how I feel at the time.
Both options require time under the cockpit, which I've already seen a lot of already in the last month.

[Slacko]

Re: A bit of fill and antifoul will sort it out.

I moved to the outside last night after sanding the daggy bits of glue on the rudder repair.
I removed the stainless steel brackets that attached the top of the rudder skeg to the hull.
This has never been very successful, the screws to the hull were the cause of the leak that I'm dealing with and always came loose.
I dug all the loose gunge out from between the hull and skeg with the multitool, then stripped all the paint off the skeg.
IMG20230323193710.jpg
I have some heavy monoaxial Carbonfibre cloth that I'm going to layer up over a nice fat fillet to the skeg/hull join and stiffen up the skeg at the same time.

[Slacko]

Re: A bit of fill and antifoul will sort it out.

Yesterday I stripped some of the paint off the hull above where the skeg is, then cut a 5mm deep 90 x 30 trench into the hull both sides beside the skeg.
I've made a pair of blocks that will be glued into them, and the carbon will lay over the top.
It was a bit punky in there, so I spent the day painting methylated spirits in there to dry the wood out.
It is working well enough that hopefully I can do the glue up tomorrow.
I switched back to inside the hull while the drying is going on, and made a pair 50 x 30 timbers to go either side of the rudder penetration and got them glued into place.

IMG20230325161748.jpg

IMG20230325161807.jpg

I'm basically ready for paint in there now, then I can reconnect all the plumbing.

[Slacko]

Re: A bit of fill and antifoul will sort it out.

This afternoon I worked on the rudder keg attachment.
I painted everything with neat epoxy,
Glued and screwed the Jarrah locating blocks into the cutouts in the hull,
then laid 3 of 90 mm wide layers of 400gsm cloth that starting with a 200 mm long one,
then longer each layer.
Finally a cover of peel ply over the top to flatten it all down.

IMG20230326173536.jpg

[Slacko]

Re: A bit of fill and antifoul will sort it out.

Today I stripped the peel ply, light sand and filled the rudder skeg with West 413.




I also sanded and primed the internal repairs. Starting to look good in there.

[Slacko]

Re: A bit of fill and antifoul will sort it out.

Since the last post I've got 2 coats of top coat paint on the internal repairs, looking good!
After some drying time, (the Altex single pack paint stays really soft for a long time after it has "cured"), I reinstated all the hoses to the transom.
Cockpit drains, bilge pumps, then the exhaust hose. Wrestling a python with that one!
Today I sanded the rudder skeg filler, primed it then got the first coat of antifoul on this and the new propeller.

[Slacko]

Re: A bit of fill and antifoul will sort it out.

I've got the rear of the engine box, and the sides forward to the cockpit floor installed.


It looks like there is plenty of space to get pieces in there until you cut them. I thought I could do the rear with 2 pieces, but ended up with 5 in the end.

The water seperator/filter unit will sit behind the entry steps as it will be too tight with the insulation.


I'm making patterns for the box that will cover the rest of the engine from MDF door skin.
I'm tapering everything to try to make it less boxy sitting there.


I've also been spending time finishing off some of the list of small jobs.
Lights in the rear lockers,
filling and painting around the old engine box demolition,
fitted the arm on the bottom of the tiller for the autopilot. I made a new arm a couple of years ago, but for some reason thought it wouldn't fit/work.
It fitted perfectly and looks great. It will be great to have autopilot again.
I have a Raymarine ST2000 I think. It doesn't have the power to sail to windward, but is fine for other points of sail and is awesome when motoring long distance.
I hooked up the depth and speed sensor wiring in the new panel, and freed up the paddlewheel with some fine sandpaper on the shaft. I'm not sure how it got the little burr on it that was stopping it from working.

Tomorrow is relaunch day and engine trials with the mechanic. Fingers crossed!

[Garret]

Re: A bit of fill and antifoul will sort it out.

We're rooting for ya!

[Slacko]

Re: A bit of fill and antifoul will sort it out.

That went really well.
The weather was more Spring than Autumn, with a tornado wreaking some havoc 50km's away on the West Coast.
After coffee and a sausage roll at the boatyard cafe, she got dropped in the water.




The engine fired up straight away and settled to a slightly fast idle.
After testing the gear shifting was correctly connected, the idle was adjusted down, the water and oil levels in the engine and gearbox oil double checked, so we headed out for a sea trial.
There was up to 30 knots blowing on the nose out of the marina, but we were seeing 8.5 Knots at 2900 revs full throttle pushing into it.
Spinning around we got 8.9 Knots with the wind behind, with a stern wave up around the top of the transom and the hull trying to climb out of the hole we were digging.
We dropped off the mechanics at the dock, and took off for town running at around 7.5 knots at 2000 rpm, varying the revs up and down every few minutes as advised by the mechanics.
It was a bit of a wet ride across the harbour with wind on the stern quarter whipping spray into the cockpit.
Happy days with a beer to celebrate getting the job done.

[Garret]

Re: A bit of fill and antifoul will sort it out.

Excellent! I hope the boat enjoyed the "coffee and a sausage roll at the boatyard cafe"...

[John B]

Re: A bit of fill and antifoul will sort it out.

8.5 knots!
Neat companionway hatch/ door, I haven't noticed that before.

[Stiletto]

Re: A bit of fill and antifoul will sort it out.

Congratulations! I'm glad it worked out so well.

[Slacko]

Re: A bit of fill and antifoul will sort it out.

Some of you may have noticed I'm a little distracted at the moment from other threads on here.
I have been working away making the new engine box.
It is in primer as I write.
Plywood, that will hinge from the floor, forward and have the break apart hinges from the old box.
The lid is cut from the old box so retains the paint finish and the noise insulation underneath that is "quite" expensive I thought when I got a 1200 square piece to line the rest of the box.

[Slacko]

Re: A bit of fill and antifoul will sort it out.

I took the box, which now has a fiddle rail around the top to check for fit.
It was pretty good considering templates I made were difficult to keep in place while making them
IMG20230508162116.jpg

I now need to install a piece of timber across the ends of the engine bed to install hinges. Once these are on, the final fettling can be done to make it sealed for noise.
There is a bit of rework around the box to tidy the area as well.
I've been making a stainless bracket for the boom winch, which has been upgraded to a 2 speed. This frees up the one I pulled off to go onto he Reactor for Halyard to replace the Murray ones in that.