Page 4 of 4 FirstFirst ... 34
Results 106 to 132 of 132

Thread: Duck Trap Wherry

  1. #106
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    Where did the time go? Life got in the way again I guess. Here's a pic of my progress so far. 2nd plank starboard side test fit. Port side 2nd plank sitting on top fits so this one should too. Lots of work with my block plane before I can glue them in place but getting there slowly.
    February 17, 2021.jpg

  2. #107
    Join Date
    Nov 2011
    Location
    Salt Spring Island, BC
    Posts
    7,965

    Default Re: Duck Trap Wherry

    How's the recovery going Roy?

  3. #108
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    Slowly, but I refuse to let it stop me doing the things I love. The sailing club just allocated a spot for my boat so I can take my "interim" rower down and start getting some good exercise. I'm already out on my bike whenever it's dry and not too cold.
    The wherry is coming along and I'm enjoying the challenges a multi strake boat presents. I'll post from time to time but prefer to show the end of each "challenge" because once I get that far nobody will be any the wiser as to what I did wrong and how I hid my mistakes. In the end she'll look good and row well.

  4. #109
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    A little progress
    March 13, 2020.jpg

  5. #110
    Join Date
    Apr 1999
    Location
    West Boothbay Harbor, Maine
    Posts
    24,882

    Default Re: Duck Trap Wherry

    "So we beat on, paddleboats against the wake of a neighbor’s jet ski, born back ceaselessly into the past." The Great Lakes Gatsby

  6. #111
    Join Date
    Nov 2011
    Location
    Salt Spring Island, BC
    Posts
    7,965

    Default Re: Duck Trap Wherry

    Every time I get about this far along I start contemplating building another of the same at twice the lengths, heights and widths but not planked any higher than right where you are. I've never done it and doubt that I ever will but it looks so good right there.

  7. #112
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    Far from perfect but after some filling and sanding it should pass muster. Once I've got the outside close to finished I'll turn her over and start on the "furniture". I'm planning to include buoyancy/storage under each end and under the rowing stations. I'm also thinking of full length seats but that will be a decision for later. At this rate I should be able to launch next spring.April 18, 2021.jpg

  8. #113
    Join Date
    Jan 2018
    Location
    Mosier Oregon
    Posts
    81

    Default Re: Duck Trap Wherry

    YESSS! Great work!

  9. #114
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    Did somebody say you can't have too many clamps?
    April 25, 2021.jpg

  10. #115
    Join Date
    Jul 2010
    Location
    northeast Ohio
    Posts
    2,801

    Default Re: Duck Trap Wherry

    Quote Originally Posted by Roy Morford View Post
    Did somebody say you can't have too many clamps?
    ...wasn't me...

    Looking good Roy.

  11. #116
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    Time out for medical stuff. Getting back now. Recently received an old 4 poster bed. The rails are veneered but the corner posts are solid mahogany. This is very old and I've already cut and planed the first leg. Beautiful colour and grain. It's very dry and brittle but that just means going slow and careful. I plan to use this wood for the breast hook, knees and other parts where I can show off this beautiful wood. Forgot to mention that the in and out wales are installed with whatever the bits are called that make it scuppered gunwales. Pics to follow.

  12. #117
    Join Date
    Apr 2011
    Location
    Vancouver, BC
    Posts
    161

    Default Re: Duck Trap Wherry

    Looking so good, Roy. Nice score on the mahogany!!

    Cheers,
    Dale

  13. #118
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    Some little progress. Next job is to turn it over, fill and sand the hull, add a cutwater and round the bottom corners of the inwales and gunwales. Glass and epoxy for the hull bottom and first strake, prime and paint, brass half oval for the keel then turn it over and an equal amount of work inside. I have a lot of old mahogany, walnut and pine that I plan to use for thwarts, knees and anything else that I'm inclined to "pretty up" with nice old wood. Easier said than done so don't hold your breath for my next post.

    2021, September 17.jpg
    Last edited by Roy Morford; 09-17-2021 at 09:02 PM.

  14. #119
    Join Date
    May 2017
    Location
    North Bend, OR. USA
    Posts
    619

    Default Re: Duck Trap Wherry

    Looking good Roy, coming right along!

    Ken
    When the desire to learn is greater than the desire to win, the journey becomes the prize.

  15. #120
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    There is a lot of recycled wood in my boat. A 100 year old mahogany coffee table, an equally old mahogany four poster bed, a solid pine coffee table and more. Today, a friend who knows I'm a scrounger, brought me a box of pine shelf supports which were surplus to the job he was doing and wondered if I could use them. Silly question! These will be perfect (after a little trimming) between the thwarts and inwales.

    2021, September 19.jpg

  16. #121
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    Another small step. Today In installed the laminated cutwater. Now I have to start the marathon sanding of the planks.

    2021, October 9.jpg

  17. #122
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    Life keeps getting in the way but here I am today.
    2022, May10.jpg

  18. #123
    Join Date
    Jun 2003
    Location
    Fredericton, New Brunswick
    Posts
    48,854

    Default Re: Duck Trap Wherry

    Very sweet.
    If I use the word "God," I sure don't mean an old man in the sky who just loves the occasional goat sacrifice. - Anne Lamott

  19. #124
    Join Date
    Jan 2018
    Location
    Mosier Oregon
    Posts
    81

    Default Re: Duck Trap Wherry

    Great work sanding!!!!

    -Derek

  20. #125
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    No pictures today because I'm sure that watching a seal coat of epoxy drying is right up there with watching paint dry. However, the last few days have been very productive and both sides of the hull have now received a seal coat of epoxy. I also purchased some brass bar to protect the keel and spent some time bending it to fit the bow and stern as well as rounding the cut ends. Next step is to sand the grain raised by the epoxy on the port side and then give the entire hull a coat or two of primer. Now I'm enjoying a cool drink while contemplating exactly how to work on part of the inside (between the top strakes and the inwales) which will necessitate creeping under the hull while it's inverted. Lots of fun.

  21. #126
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

  22. #127
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    Not sure why the picture was posted 3 times. Technology, what can I say.

    I've now completed the primer coat on both sides and spent several hours sanding it back to an acceptable level and ready to paint the final coat. Before that I plan to cut the brass keel strip to shape, drill the holes for securing to the hull and then drill the corresponding holes on the hull itself. Once the final coat is finished I'll fix the keel strip in place and probably (depending on availability) use Dolfinite to bed it down.

    Finally beginning to look like a boat!

  23. #128
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    The keel strips now have all the holes drilled and test fit to the hull with steel screws. I now have to remove the strips, countersink all the holes and then put everything somewhere safe until the hull painting is finished. I'll be fixing the strips with bronze screws because brass screws have a tendency to break with even a small amount of force.

    2022, May 23.jpg
    Attached Images Attached Images
    Last edited by Roy Morford; 05-24-2022 at 09:36 AM.

  24. #129
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    Previous post showed a picture 3 times. This one shows the picture twice. Maybe the next post I'll get it right. Technology and advancing years don't mix too well!!!

  25. #130
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    Today I put the first coat of Interlux white on the hull and, in spite of taking it very carefully, I still ended up with a few small holidays and a couple of small curtains. Now worries, a second coat should fix things and, if not, there's always the third coat!

  26. #131
    Join Date
    Jun 2002
    Location
    Vancouver, BC
    Posts
    981

    Default Re: Duck Trap Wherry

    Did I mention that a newly painted hull is like a giant fly trap?

  27. #132
    Join Date
    Jul 2010
    Location
    northeast Ohio
    Posts
    2,801

    Default Re: Duck Trap Wherry

    oh yeah!
    the hardest part is to just them be...and after the paint is dry those little legs just snap off and you'll hardly see anything in the paint.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •