Page 2 of 2 FirstFirst 12
Results 36 to 58 of 58

Thread: Building Ninigret

  1. #36
    Join Date
    Jan 2008
    Location
    Lake Champlain, Vermont
    Posts
    2,669

    Default Re: Building Ninigret

    Take a look at this thread,Thread: "Skål Sandy!” a Caledonia Yawl Build in Cream Ridge NJ

    the building of a Caledonia Yawl. Glued lap (epoxy) no frames, no rivets I have sailed in Geoff Kerr's CL that was built many years ago using this method, still like new.

  2. #37
    Join Date
    Sep 2010
    Location
    Bainbridge Island WA
    Posts
    2,549

    Default Re: Building Ninigret

    Quote Originally Posted by timo4352 View Post
    One thing that's bugging me about epoxy is it being brittle. Something is telling me I want something with some flex to it. I've considered G-Flex to solve that worry. The other glues 5200, 4200, Sika have some flex.
    The number of old epoxy-glued boats still floating around ought to dispel your concerns. What drives your idea that it is somehow too brittle?
    Steve

    Boats, like whiskey, are all good.
    R.D Culler

  3. #38
    Join Date
    Jul 2010
    Location
    northeast Ohio
    Posts
    1,691

    Default Re: Building Ninigret

    some reading on brittleness:
    https://epoxyworks.com/index.php/if-...more-flexible/

    https://www.jamestowndistributors.co...t.do?docId=357

    my fears could be unfounded, but maybe not...

    ...or maybe deep down inside I just don't want to use epoxy for this build...IDK...
    Last edited by timo4352; 10-03-2018 at 10:29 AM.

  4. #39
    Join Date
    Sep 2010
    Location
    Bainbridge Island WA
    Posts
    2,549

    Default Re: Building Ninigret

    Both of those articles come to more or less the same conclusion, the wood substrate will tend to fail before the epoxy does. I worry more about the quality of mass-produced marine plywood than the epoxy I mix up and apply myself.

    My intention is for my next big build to be cedar planks on steam-bent oak frames so I get not wanting to use epoxy to hold the boat together but it is a very good structural adhesive.
    Steve

    Boats, like whiskey, are all good.
    R.D Culler

  5. #40
    Join Date
    Jun 2011
    Location
    Central New Jersey
    Posts
    897

    Default Re: Building Ninigret

    Disclaimer: I am an opinionated rank amateur!

    Just a suggestion, take two relatively long ( 2' t0 3') strips (3" to 4" wide) of plywood that are thin enough that you can twist them some by your hand. Make a 3/4 to 1' lap joint with a filler like wood flower or west laminating filler and let the joint cure for a few days. Once fully cured twist it until it breaks, if you can't break it bend it over something until it breaks. What failed the wood or glue joint.

    One more thing to consider when building with plywood, every nail or screw penetration is an avenue for moisture to find its way between the plys.

    It is your boat, do it your way!

    I did! Despite numerous warnings I've made the majority of my non-plank components from locally sourced slash cut black locust. The standard is Doug Fir. I have paid a price it, any cutting, planing, shaping has taken longer and required more effort than working with DF. Oh, then there is the frequent tool sharpening and the worn out planer blades.

    I am hoping to see the progress on your build however you choose to proceed.
    Steamboat

    I get by with the judicious use of serendipity.

  6. #41
    Join Date
    Dec 2012
    Location
    Providence, RI USA
    Posts
    1,356

    Default Re: Building Ninigret

    Hi Timo,

    I'd vote for no epoxy just because that sounds like a pleasant way to build, and it's what I'd like to try for my next one. But for that I'll build small, like Atkin's Nina.

    Ninigret is a lot of boat to construct. Perhaps going with a method you're familiar with might be good, then go full trad. on a next, smaller boat. (I'm also considering the Norwegian Pram.)

    Anywhoo, I'll be following along as usual. Good luck!

    Mike
    "near it, a small whale-boat, painted red and blue, the delight of the king's old age."

  7. #42
    Join Date
    Jul 2010
    Location
    northeast Ohio
    Posts
    1,691

    Default Re: Building Ninigret

    Got the strongback 95% complete.
    The lofting table will be on top of that.
    Some kind of progress anyhow.

  8. #43
    Join Date
    Jul 2010
    Location
    northeast Ohio
    Posts
    1,691

    Default Re: Building Ninigret

    ...and finished the lofting table today.
    First coat of paint on. I'll do a second coat tomorrow. Should be ready to start the lofting by the end of the week.
    Maybe sooner depending on how anxious I get --- which is pretty much....

    Reminds me of "the scale of the thing" thread... the lofting table looks huge in my shop.

  9. #44
    Join Date
    Jul 2010
    Location
    northeast Ohio
    Posts
    1,691

    Default Re: Building Ninigret

    I took off work for the rest of the week for some much needed time off.
    Got started on the lofting today. I don't go back to work until Monday so we'll see how far I get.
    It's a start.
    IMGP0075.jpg

  10. #45
    Join Date
    Feb 2007
    Location
    Blue Hill, ME
    Posts
    962

    Default Re: Building Ninigret

    Now you've really started! Seeing that great expanse of white is exciting and disconcerting as you can now see the size and scope of the project ahead. It's great fun seeing the shape reveal itself as those numbers from the table of offsets become sweet lines.
    Steve B
    TraditionalSmallCraft.com
    RIVUS 16' Melonseed
    PAYTON 13' Pea Pod

    "If a man must be obsessed by something, I suppose a boat is as good as anything, perhaps a bit better than most." E. B. White

  11. #46
    Join Date
    Jun 2011
    Location
    Central New Jersey
    Posts
    897

    Default Re: Building Ninigret

    Good idea to take the time off for lofting, can focus and make good progress. Doing that kind of work in little snippets of time has its problems.
    Steamboat

    I get by with the judicious use of serendipity.

  12. #47
    Join Date
    Sep 2010
    Location
    Bainbridge Island WA
    Posts
    2,549

    Default Re: Building Ninigret

    Quote Originally Posted by timo4352 View Post
    I took off work for the rest of the week for some much needed time off.
    Got started on the lofting today. I don't go back to work until Monday so we'll see how far I get.
    It's a start.
    IMGP0075.jpg


    What is that batten made of?
    Steve

    Boats, like whiskey, are all good.
    R.D Culler

  13. #48
    Join Date
    Jul 2010
    Location
    northeast Ohio
    Posts
    1,691

    Default Re: Building Ninigret

    I made the battens from MDF. Painted black. This one is 3/4" X 1-1/2". Also cut some 3/4" X 1" for tighter bends - that worked OK for the stem on the 3/4" edge.
    I had to stop - I hit a couple hiccups that are making my brain hurt... I'll go back to it in the morning - fresh.

  14. #49
    Join Date
    Jul 2010
    Location
    northeast Ohio
    Posts
    1,691

    Default Re: Building Ninigret

    ...still stuck in lofting limbo...
    I have sent my question off to Pat Atkin but not sure what I'll get back...
    My question:
    "I am lofting Ninigret and I am having trouble figuring out the rabbet on the stem.It seems to me that I would need a height above the baseline or the LWL to the waterlines LL2, LL4 and LL6. Or maybe a note that the rabbet is a consistent width from station O to the sheer possibly?
    I cannot find anything in the plans that gives me this information."
    ..so what I have here is no info to locate the rabbet going up the stem. It does not appear to be a constant width from the drawings.
    The other thing that has me stumped is the offsets say "Dimensions given in feet and inches to the outside of planking" --- if this is the case, then when I draw the stem that line should be the outside of the planking also...no? -- but they show the rabbet drawn inside, so obviously the line is to the outside of the stem - not the planking.
    What gives?
    Maybe this pic will help --- those waterlines shown are LL2, LL4 and LL6 as mentioned.

    Ninigret-2 (1).jpg
    Attached Images Attached Images

  15. #50
    Join Date
    Jul 2010
    Location
    northeast Ohio
    Posts
    1,691

    Default Re: Building Ninigret

    OK - I think I got over this hurdle...
    Forgetting about the rabbet because I'm thinking it will be simpler to do a two piece stem anyways....
    Good thing I've got some good, big erasers on hand ...

    So when I project my stem down to the plan drawing,.. and figure out my landing on the stem for the planking - I get a line I can work with. Project that line back up to the top of the stem, and measure across to the front of the stem, I get 1-1/2"...
    ...now I can square that up off my baseline at the LL2, LL4 and LL6 waterlines to get those same 1-1/2" points. Tap in a few nails, connect the dots with a batten, and I think I'm setup for my two piece stem. This makes my outer, or false stem that 1-1/2" thick which should be good. I hope.
    Sound like a plan? Or does my rambling make any sense to anyone but me?
    Maybe I just needed to talk myself through it...
    Or maybe I'm dead wrong...

  16. #51
    Join Date
    Sep 2010
    Location
    Bainbridge Island WA
    Posts
    2,549

    Default Re: Building Ninigret

    "Dimensions given in feet and inches to the outside of planking"

    That means you have been given the outside faces of a boat-shaped object and when you get around to making the frames you will need to subtract the thickness of the sheathing from the frames so the finished boat more or less matches you drawn dimensions. There are a few ways to go about accounting for the thickness but on this size boat I think you can simply subtract the thickness of the plywood and be just fine.

    That also means that the drawn line of the stem is where the finished piece should end up.

    The rabbet should be somewhere on the plans. Could be in the table of offsets or on the drawing as "X inches back from the face of the stem along waterline Y" or from the forward perpendicular. Keep plugging away at it, the solution should show itself as you go. Even going with a two-piece stem you will still need to find where the planking intersects with the stem, you should be able to develop that from the half-breadths once you get them drawn. I have done just enough of this stuff to be dangerous and my grasp of the subject/writing skills are not solid enough for me to get super-didactic about the applied geometry of lofting, hopefully someone more adept than I will come along. Or someone who has built Ninigret will stop by and say "Oh that is in the lower left corner of page 3".
    Steve

    Boats, like whiskey, are all good.
    R.D Culler

  17. #52
    Join Date
    Jul 2010
    Location
    northeast Ohio
    Posts
    1,691

    Default Re: Building Ninigret

    Thanks Steve
    I felt like I was stuck there, and there was no sense moving forward to doing the body plan...
    ...but I feel pretty confident in this approach that it is safe to proceed -- if I'm wrong I still have a few erasers handy.

    The planking deduction... I know that has to happen. Still contemplating just how I want to accomplish that. Seems to me taking the angled deduction off the plan lofting would be the most accurate, but yes, the difference looks minimal from just taking it right off the frames. Maybe leave them a little heavy and do a little more fairing once it's all set up.

  18. #53
    Join Date
    Feb 2007
    Location
    Blue Hill, ME
    Posts
    962

    Default Re: Building Ninigret

    I had just made a bevel board, per Gudgeon's manual, for figuring the plank deduction when Paul Gartside stopped by before I used it (he was teaching a class down the road at WBS) and said it wasn't necessary. Of course I took his word for it, glad to have one less calculation. Like the other Steve, I know just enough about lofting to be dangerous, to get it done, but I could be missing the finer points. So I don't know if that applies to your design or that is just how Gartside's designs work.
    Steve B
    TraditionalSmallCraft.com
    RIVUS 16' Melonseed
    PAYTON 13' Pea Pod

    "If a man must be obsessed by something, I suppose a boat is as good as anything, perhaps a bit better than most." E. B. White

  19. #54
    Join Date
    Jul 2010
    Location
    northeast Ohio
    Posts
    1,691

    Default Re: Building Ninigret

    Well i have pushed ahead and I think, pretty much, finished the lofting. This hard chine design makes doing the body plan pretty easy.

    I did not have the room to expand the transom out -- so I superimposed it (in a different color). I hope that is not going to come back to bite me...

    Did a quick check plotting off the LWL on the plan view and it looks good.

    --So question is: with this hard chine design do you see any need for me to draw those additional waterlines in plan view?
    -- and should I go to the trouble to add buttocks to the body and profile?
    Or is this just a waste of time and added complication for no gain?
    I'm thinking the latter, but what do you guys think?

  20. #55
    Join Date
    Jan 2008
    Location
    Lake Champlain, Vermont
    Posts
    2,669

    Default Re: Building Ninigret

    What do your lofting books say? Seems like doing it all will give a better picture, plus lofting is fun. Right?

  21. #56
    Join Date
    Nov 2011
    Posts
    5,417

    Default Re: Building Ninigret

    It seems to me that additional WLs, buttocks and diagonals would be useless with the straight frames.

    You're going to build upside down, right? It might help later if you mark the LWL on the transom, then before you flip it you can use it and a laser level to mark it all the way around. That's also a good time to completely finish the bottom.

  22. #57
    Join Date
    Jul 2010
    Location
    northeast Ohio
    Posts
    1,691

    Default Re: Building Ninigret

    Suddenly it occurs to me that just maybe the designer knows a bit more than me about it... He did not include any of those additional lines in his plans, most probably because they were not necessary, so why would I ?
    Maybe I just answered my own stupid question... and I said I didn't want to be asking any stupid questions...
    Go figure.

  23. #58
    Join Date
    Sep 2010
    Location
    Bainbridge Island WA
    Posts
    2,549

    Default Re: Building Ninigret

    I wouldn't add many extra lines either. However, since it will never be easier than now I would mark for things like the cockpit sole and berth tops. That will give you 3 good reference planes to check for plumb as you go forward and you'll already know where the internal framing pieces go when the build gets to that point. A laser level works but can be a bit fiddly to set up, is pestered by vibration and only works line-of-sight so inevitably the place you really want a mark will be in shadow.
    Steve

    Boats, like whiskey, are all good.
    R.D Culler

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •