Page 2 of 2 FirstFirst 12
Results 36 to 52 of 52

Thread: Building the revised Gorewood 16' Canoe - second attempt

  1. #36
    Join Date
    May 2009
    Location
    Vienna, Austria
    Posts
    470

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    Because of some problems with my back two months ago I had to take a break from the build.

    After everything was back to normal I was able to continue.

    Before glassing the hull I give the most prominent part of the humps a little sanding.


    This is the one of the areas that gets sanded:


    Nowhere sanded through the outer veneer which means that I took off less than 1.2 mm.


    After sanding there is not much difference but the contour is a tad smoother.


    So the hull is ready for glassing.

  2. #37
    Join Date
    Aug 2005
    Location
    SF Bay Area- Richmond
    Posts
    15,169

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    Amazing!!! And very well documented.
    "The enemies of reason have a certain blind look."
    Doctor Jacquin to Lieutenant D'Hubert, in Ridley Scott's first major film _The Duellists_.

  3. #38
    Join Date
    May 2009
    Location
    Vienna, Austria
    Posts
    470

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    The 6 oz. glass cloth I use is 100 cm wide.
    The two panels of cloth for the outside of the hull overlap by about 60 cm at the middle of the hull with the overlap narrowing towards the ends.






    I installed the rub rail (made of ash) before the last coat of epoxy is fully cured.


    Sculptured a kneeling thwart:


    Last edited by flo-mo; 07-19-2017 at 03:46 AM.

  4. #39
    Join Date
    May 2009
    Location
    Vienna, Austria
    Posts
    470

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    Helmut Schierer, a fellow canoe enthusiast and photographer visited me when I was glassing the hull.
    He took photos to create another one of his amazing panoramic images: http://www.rundumadum.at/detail/ru/2...olterer-teil-2

    That would be handy if there were 9 copies of me for some part of the work.
    I wonder how well we would get along.

  5. #40
    Join Date
    May 2009
    Location
    Vienna, Austria
    Posts
    470

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    I already know that the Gorewood 12 Canoe fits inside the Gorewood 14 Canoe so I can easily car-top both.





    But would the 14' also fit inside the 16' canoe?





    Yes, it does. So on the rare occasion when I want to car-top all three canoes, now I know that it is possible.

  6. #41
    Join Date
    Feb 2001
    Location
    Stevens Point, Wi, USA
    Posts
    2,273

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    Very nice work.
    The best helping hand you will ever receive is the one at the end of your own arm.

  7. #42
    Join Date
    Feb 2001
    Location
    Stevens Point, Wi, USA
    Posts
    2,273

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    Any idea how much they weigh?
    The best helping hand you will ever receive is the one at the end of your own arm.

  8. #43
    Join Date
    Jul 2016
    Location
    Courtenay, B.C., Canada
    Posts
    11

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    Beyond impressive.

  9. #44
    Join Date
    Apr 2012
    Location
    Louisville, KY
    Posts
    630

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    It's matryoshka canoes! Make sure you get a picture of peoples' faces when you pull up to the launch site and start pulling canoes out of canoes.

  10. #45
    Join Date
    May 2009
    Location
    Vienna, Austria
    Posts
    470

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    The dimensions of the inner gunwales are 23 x 18 mm (made of two strips of spruce), which is absolute minimalist all to save weight.
    Therefor I think it is necessary to beef up the area where the seats are installed.
    These pieces are made of cherry and will support the gunwale where the seats will hang. Also shown are the wedges for mounting the kneeling thwart.



    I skipped to take photos of glassing the inside of the hull.
    So after the thwarts and seats are installed, the canoe is ready to go.








  11. #46
    Join Date
    May 2009
    Location
    Vienna, Austria
    Posts
    470

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    Quote Originally Posted by Iceboy View Post
    Any idea how much they weigh?
    Gorewood 12: 10 kg (22.2 lbs)
    Gorewood 14: 13.5 kg (30 lbs)
    Gorewood 16: 23 kg (51.1 lbs)

    When I started this build I was hoping to keep the weight for the 16 ft canoe under 20 kg.
    But then I had a mishap with my Gorewood 14.
    On portage I tripped, the canoe landed on a rock and unluckily I fell with the whole weight of my body onto the canoe. The result of this accident was a severe damage of the canoe.











    I managed to repair the hole, but because of this incident I reconsidered my plan to use 3 oz. glass cloth for the 16 ft canoe, which is just what I used for the 14 ft canoe.
    I chickened out and I ended up using 6 oz. glass instead, which is a saver option.

    Therefor the weight of the canoe is 3 kg over my declared goal, but if your are willing to take the risk, it should be possible to keep the weight under 20 kg.

  12. #47
    Join Date
    Feb 2001
    Location
    Stevens Point, Wi, USA
    Posts
    2,273

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    Very light for their size. Beautiful work. Thank you for the thread.
    The best helping hand you will ever receive is the one at the end of your own arm.

  13. #48
    Join Date
    May 2009
    Location
    Vienna, Austria
    Posts
    470

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    Christening the canoe - Liv, a Nordic blonde (and also live long and prosper).












  14. #49
    Join Date
    May 2009
    Location
    Vienna, Austria
    Posts
    470

    Default Re: Building the revised Gorewood 16' Canoe - second attempt




  15. #50
    Join Date
    Jul 2015
    Location
    Frenchman's Cove, Newfoundland and Labrador, Canada
    Posts
    138

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    Wow, what a beautiful canoe! One has to look so closely to see the gores, looks almost cold molded.

    I love how the different sizes nest like Russian dolls.

    Great to see how well the repair worked on the 14.

    I also noticed with interest how you had to take out a bit of wood along the keel line to get rid of the bumps and reduce the hollow in the middle. I'm not quite sure yet if my "butterfly boats" will be affected by the same issue; my paper models are a bit too crude to be conclusive. My signboard boat definitely has this problem but at least you don't see it when it is in the water. Whenever I've modeled a boat in Freeship that had more plumb ends and less rake, the panels came out as needing to be hollowed along the keel line just like this Gorewood canoe.

    I'm still working on a butterfly boat design that also avoids "that stitch and glue look" with the large panels and sharp chines while keeping the torture to a minimum. I guess the key to avoid having each chine or gore too prominent is to have more of them.

  16. #51
    Join Date
    Apr 2015
    Location
    Red Hook, NY
    Posts
    82

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    Quote Originally Posted by flo-mo View Post
    One more time I want to emphasize this astonishing way of displaying my workshop by courtesy of a friend:

    http://www.rundumadum.at/images/ru/P...02_1407/t.html

    http://www.rundumadum.at/images/ru/P...01_1407/t.html
    So this is how you get so much done....there are two of you...cool 360 your friend captured and awesome build. Thank you for sharing.

  17. #52
    Join Date
    May 2009
    Location
    Vienna, Austria
    Posts
    470

    Default Re: Building the revised Gorewood 16' Canoe - second attempt

    Quote Originally Posted by Hreoaj View Post
    So this is how you get so much done....there are two of you...cool 360 your friend captured and awesome build. Thank you for sharing.
    That is nothing -- look at the nine of us : http://www.rundumadum.at/images/ru/P...03_1407/t.html

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •