Drill bit boxes

[cs]

I've been trying to find a metal box for storing drill bits similar to below:



It seems that the only way you can get the box is to buy the set. I don't need the set but I do like that type of box and I could use it to store the bits I already have. If anyone knows a source please let me know.

Chad

[cs]

I've been trying to find a metal box for storing drill bits similar to below:



It seems that the only way you can get the box is to buy the set. I don't need the set but I do like that type of box and I could use it to store the bits I already have. If anyone knows a source please let me know.

Chad

[cs]

I've been trying to find a metal box for storing drill bits similar to below:



It seems that the only way you can get the box is to buy the set. I don't need the set but I do like that type of box and I could use it to store the bits I already have. If anyone knows a source please let me know.

Chad

[Dale Genther]

McMaster Carr has exactly what you posted the photo of. Cost $28.45 to $32.36 dpeending of drill size.

[Dale Genther]

McMaster Carr has exactly what you posted the photo of. Cost $28.45 to $32.36 dpeending of drill size.

[Dale Genther]

McMaster Carr has exactly what you posted the photo of. Cost $28.45 to $32.36 dpeending of drill size.

[Tom Dugan]

http://www.mcmastercar.com - under "machining"

Master Combination Cases for Jobbers' Length Drills
1/16"— 1/2" x 64ths,
A—Z, and Nos. 1—60 115 13 1/2" x 4 5/8" x 2 1/4" 2798A12* $28.45

This one looks way cooler,

but it's $270

-T

[Tom Dugan]

http://www.mcmastercar.com - under "machining"

Master Combination Cases for Jobbers' Length Drills
1/16"— 1/2" x 64ths,
A—Z, and Nos. 1—60 115 13 1/2" x 4 5/8" x 2 1/4" 2798A12* $28.45

This one looks way cooler,

but it's $270

-T

[Tom Dugan]

http://www.mcmastercar.com - under "machining"

Master Combination Cases for Jobbers' Length Drills
1/16"— 1/2" x 64ths,
A—Z, and Nos. 1—60 115 13 1/2" x 4 5/8" x 2 1/4" 2798A12* $28.45

This one looks way cooler,

but it's $270

-T

[Donn]

great website...what don't they have?

[Donn]

great website...what don't they have?

[Donn]

great website...what don't they have?

[cs]

Thanks for the rapid reply. Went to the site ordered the Master combination case and it is on its way.

Chad

[This message has been edited by cs (edited 02-07-2002).]

[cs]

Thanks for the rapid reply. Went to the site ordered the Master combination case and it is on its way.

Chad

[This message has been edited by cs (edited 02-07-2002).]

[cs]

Thanks for the rapid reply. Went to the site ordered the Master combination case and it is on its way.

Chad

[This message has been edited by cs (edited 02-07-2002).]

[Dave Fleming]

From the for what its worth dept..
MMC catalogues are highly prized even e-*** has auctions of them!
Lets see if 'cs' get one now that he has ordered from them.

dave: who regularly gets his MMC catalogue and promply gives the older one to his friendly neighborhood machine shop.
Those little things pay off believe me.

[Dave Fleming]

From the for what its worth dept..
MMC catalogues are highly prized even e-*** has auctions of them!
Lets see if 'cs' get one now that he has ordered from them.

dave: who regularly gets his MMC catalogue and promply gives the older one to his friendly neighborhood machine shop.
Those little things pay off believe me.

[Dave Fleming]

From the for what its worth dept..
MMC catalogues are highly prized even e-*** has auctions of them!
Lets see if 'cs' get one now that he has ordered from them.

dave: who regularly gets his MMC catalogue and promply gives the older one to his friendly neighborhood machine shop.
Those little things pay off believe me.

[Dale Genther]

McMasters has been my secret source of boating stuff for a long time now. They have all kinds of good stuff; shackles, clevis pins, cotter pins, fasteners, chain, wire rope, etc. And it isn't labled "marine" so it doesn't carry the usual markup. BTW a boating friend of mine says he must have a marine wife because she costs twice as much to maintain as other wives.

[Dale Genther]

McMasters has been my secret source of boating stuff for a long time now. They have all kinds of good stuff; shackles, clevis pins, cotter pins, fasteners, chain, wire rope, etc. And it isn't labled "marine" so it doesn't carry the usual markup. BTW a boating friend of mine says he must have a marine wife because she costs twice as much to maintain as other wives.

[Dale Genther]

McMasters has been my secret source of boating stuff for a long time now. They have all kinds of good stuff; shackles, clevis pins, cotter pins, fasteners, chain, wire rope, etc. And it isn't labled "marine" so it doesn't carry the usual markup. BTW a boating friend of mine says he must have a marine wife because she costs twice as much to maintain as other wives.

[TomRobb]

[TomRobb]

[TomRobb]

[cs]

Got the box in today. Quick service. Now all someone has to do is explain what the A-Z & 1-60 slots are for.

Chad

[cs]

Got the box in today. Quick service. Now all someone has to do is explain what the A-Z & 1-60 slots are for.

Chad

[cs]

Got the box in today. Quick service. Now all someone has to do is explain what the A-Z & 1-60 slots are for.

Chad

[Tom Dugan]

Uuuuuuhhhhhhhnnnnmmmmmmm.

Nope. I couldn't give a complete answer. Better try here.


-T

[Tom Dugan]

Uuuuuuhhhhhhhnnnnmmmmmmm.

Nope. I couldn't give a complete answer. Better try here.


-T

[Tom Dugan]

Uuuuuuhhhhhhhnnnnmmmmmmm.

Nope. I couldn't give a complete answer. Better try here.


-T

[Ed Harrow]

Machinery's Handbook and McMaster-Carr.

Solve anything. Fast.

Number and letter sizes are for drilling holes which will be tapped for threads.

[Ed Harrow]

Machinery's Handbook and McMaster-Carr.

Solve anything. Fast.

Number and letter sizes are for drilling holes which will be tapped for threads.

[Ed Harrow]

Machinery's Handbook and McMaster-Carr.

Solve anything. Fast.

Number and letter sizes are for drilling holes which will be tapped for threads.

[Ed Harrow]

And now for a real drill index:

[Ed Harrow]

And now for a real drill index:

[Ed Harrow]

And now for a real drill index:

[NormMessinger]

Cs, says, "Now all someone has to do is explain what the A-Z & 1-60 slots are for."

That's easy. 60 + 26 = 86 . Yup, they are for 86 bits.

In the U.S., at least, there is a range of bits measured in fractions, 1/64" increments in the smaller sizes. And another range of numbered and lettered, 1 being small 60 big, A a little bigger still and Z a lot bigger. I've not used them in woodworking. I think they are measured in thousanths however.

--Norm

[NormMessinger]

Cs, says, "Now all someone has to do is explain what the A-Z & 1-60 slots are for."

That's easy. 60 + 26 = 86 . Yup, they are for 86 bits.

In the U.S., at least, there is a range of bits measured in fractions, 1/64" increments in the smaller sizes. And another range of numbered and lettered, 1 being small 60 big, A a little bigger still and Z a lot bigger. I've not used them in woodworking. I think they are measured in thousanths however.

--Norm

[NormMessinger]

Cs, says, "Now all someone has to do is explain what the A-Z & 1-60 slots are for."

That's easy. 60 + 26 = 86 . Yup, they are for 86 bits.

In the U.S., at least, there is a range of bits measured in fractions, 1/64" increments in the smaller sizes. And another range of numbered and lettered, 1 being small 60 big, A a little bigger still and Z a lot bigger. I've not used them in woodworking. I think they are measured in thousanths however.

--Norm

[Tom Dugan]

OK, so if youze guys are gonna make me browse around in the McMaster Carr website, I might as well point out that if you look under "Raw Materials" - "metal" - "steel" - "Drill Rod", you can click on the "letter sizes" or "number sizes" to get the sizes in thousandths of an inch fer each.

Now as to [i]why[/] they are numbered and lettered, weellllll, sorry. Ain't got a clue.

-T

[Tom Dugan]

OK, so if youze guys are gonna make me browse around in the McMaster Carr website, I might as well point out that if you look under "Raw Materials" - "metal" - "steel" - "Drill Rod", you can click on the "letter sizes" or "number sizes" to get the sizes in thousandths of an inch fer each.

Now as to [i]why[/] they are numbered and lettered, weellllll, sorry. Ain't got a clue.

-T

[Tom Dugan]

OK, so if youze guys are gonna make me browse around in the McMaster Carr website, I might as well point out that if you look under "Raw Materials" - "metal" - "steel" - "Drill Rod", you can click on the "letter sizes" or "number sizes" to get the sizes in thousandths of an inch fer each.

Now as to [i]why[/] they are numbered and lettered, weellllll, sorry. Ain't got a clue.

-T

[Hugh Paterson]

Christ Ed you sure your wall is strong enough to hang on to all that steel?

Shug.

[Hugh Paterson]

Christ Ed you sure your wall is strong enough to hang on to all that steel?

Shug.

[Hugh Paterson]

Christ Ed you sure your wall is strong enough to hang on to all that steel?

Shug.

[Ross Faneuf]

The letter and number size drills date back to some time in the 1800s. I don't know all the history, but do know they were systems which provided intermediate drill sizes between the fractional sizes. The number sizes in particular supply a lot of very small drills - look up the tap drill and clearance sizes for #1x64 threads (53), for instance. Some of the number drills are related to wire sizes. If you go through the table of American tap drill sizes for machine screws, you will notice several which use either number or letter sizes, particular in small sizes. Someone into the history of machine tools in America can doubtless supply more (and more accurate) info. Possibly these were invented when the twist drill was invented (1864 by Morse), but I don't know.

[ 02-19-2002, 04:00 PM: Message edited by: Ross Faneuf ]

[Ross Faneuf]

The letter and number size drills date back to some time in the 1800s. I don't know all the history, but do know they were systems which provided intermediate drill sizes between the fractional sizes. The number sizes in particular supply a lot of very small drills - look up the tap drill and clearance sizes for #1x64 threads (53), for instance. Some of the number drills are related to wire sizes. If you go through the table of American tap drill sizes for machine screws, you will notice several which use either number or letter sizes, particular in small sizes. Someone into the history of machine tools in America can doubtless supply more (and more accurate) info. Possibly these were invented when the twist drill was invented (1864 by Morse), but I don't know.

[ 02-19-2002, 04:00 PM: Message edited by: Ross Faneuf ]

[Ross Faneuf]

The letter and number size drills date back to some time in the 1800s. I don't know all the history, but do know they were systems which provided intermediate drill sizes between the fractional sizes. The number sizes in particular supply a lot of very small drills - look up the tap drill and clearance sizes for #1x64 threads (53), for instance. Some of the number drills are related to wire sizes. If you go through the table of American tap drill sizes for machine screws, you will notice several which use either number or letter sizes, particular in small sizes. Someone into the history of machine tools in America can doubtless supply more (and more accurate) info. Possibly these were invented when the twist drill was invented (1864 by Morse), but I don't know.

[ 02-19-2002, 04:00 PM: Message edited by: Ross Faneuf ]

[David Tabor (sailordave)]

Ah, now here is something you probably don't know! It isn't in their catalog or on the web page but Jamestown Distr. has drill indexes. Yep the metal box for bits in 1/64 increments for 1/16" to 1/2" bits cost about 8.50 or so. I just ordered two for a buddy when I placed my last order!

[David Tabor (sailordave)]

Ah, now here is something you probably don't know! It isn't in their catalog or on the web page but Jamestown Distr. has drill indexes. Yep the metal box for bits in 1/64 increments for 1/16" to 1/2" bits cost about 8.50 or so. I just ordered two for a buddy when I placed my last order!