Search:

Type: Posts; User: CundysHarbor

Page 1 of 15 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    25
    Views
    1,614

    Re: Torqedo owners - Heads Up!

    Thanks for the heads up. My Torquedo is going to get a plastic pin. It'll shear at a lower load but thats a pretty insignificant matter.
  2. Re: Bunks vs Pivot rollers on a trailer for a flat bottomed plywood boat

    I keep the boat aft of the bow stop by a few inches and make sure that the lines or straps securing the boat prevent forward motion. In all situations except a disasterous crash this should keep the...
  3. Thread: Beards

    by CundysHarbor
    Replies
    67
    Views
    1,906

    Re: Beards

    And things are a lot less repairable now than formerly. . Even diesel engines are one great big computer system.
  4. Replies
    8
    Views
    445

    Re: Epoxy stains on mahogany

    Dusty has it right, it will disappear. Won't hurt to sand to make it less slick before varnishing.
  5. Replies
    19
    Views
    857

    Re: Sander dust collection

    very interesting......how is the noise level?
  6. Re: Getting a Nutshell Pram ready for the dinghy dock.

    Most Nutshells i've seen spend the summers in the water. 3/4 round rail guard all around and of course bottom paint are absolutely necessary. You may have to put risers on the oarlocks to keep the...
  7. Replies
    20
    Views
    680

    Re: Drilling lead keel for bolt holes

    Your boat was probably not designed for having a 900 lb weight on it when inverted. It was definitely not designed to have a 900 lb weight dropped on it when inverted. Here is what I did with a...
  8. Replies
    13
    Views
    611

    Re: Sources for WRC veneer?

    America's Wood in Washington, Maine is where I bought my WRC for double diagonal sheathing. The stock was excellent. PM if you have questions.
  9. Replies
    31
    Views
    1,702

    Removing masking tape

    I've wondered over the years if there is a best way to remove masking tape. I'm not talking about tape that has been on too long and is really stuck. Rather, tape that has been on for a few hours...
  10. Replies
    28
    Views
    2,234

    Re: rhodes sailboat craigslist NJ $700

    I believe she is not an Arrowhead. I owned one in Annapolis in the early 60's. A very nice day boat but there were no cockpit seats, one sat on the deck.
  11. Re: Yanmar 2GM20 owners past and present please report!

    The Yanmar 2GM20 is a great little engine. The only thing I changed on mine was to add a remote oil filter. The standard location makes changing the filter a controlled oil spill. Conversion parts...
  12. Replies
    22
    Views
    1,225

    Re: New to the Forum

    She has always been kept in very sharp Bristol fashion, in spite of the fact that she scalloped in winter. You have a nice boat there; one that has given thousands of people a taste of Penobscot bay...
  13. Replies
    123
    Views
    5,128

    Re: He tweeted what?

    He is on his way to being cornered, a cornered animal can be very dangerous. Please takes his nukes away.
  14. Replies
    45
    Views
    2,381

    Re: Scarf vs. butt joints

    I've used the Payson joint and of course tapered joint. The Payson should be done on both sides of the stock, do one side, wait for it to cure and then do the other side. Of course the cure time is...
  15. Replies
    64
    Views
    3,845

    Re: Kayak Building Questions

    Re the double kayak concept. Rent one first......they don't call them divorce boats for nothing.
  16. Replies
    7
    Views
    510

    Re: Resin turned milky

    I made a little insulated oven (foam lining in a plywood container) powered by a light bulb using a line voltage thermostat. This has kept epoxy nice and fluid over the past ten years. It is handy...
  17. Replies
    23
    Views
    1,357

    Re: Cold molded Bangor Packet

    RE the question of whether or not to glass the cold molded version: For my Joel White cold molded sloop, I was advised to put a thin (4 oz) layer of glass over the diagonal "planking" to prevent...
  18. Replies
    6
    Views
    604

    Re: Copper Green and Epoxy

    If it were me, I would do a little test using scrap.
  19. Replies
    44
    Views
    1,936

    Re: cold molding, maybe?

    Fiberglass over the strips will harden up the surface a little and, most important, prevent the strips from showing (printing) through the paint.
  20. Replies
    32
    Views
    1,526

    Re: Pitch Pockets Please?

    If you do nothing, the pitch will lift the varnish. I'd dig it out and epoxy a dutchman in.
  21. Replies
    21
    Views
    1,243

    Re: Interlux Schooner problems

    Don't remove the lid...punch holes in the lid for pouring varnish and seal the holes with sheet metal screws. This actually works.
  22. Re: recommended distance between skeg and prop? ocean pointer

    FWIW, I built mine to the design and have no reason to believe the boat would be better with a modified keel.
  23. Replies
    18
    Views
    988

    Re: Epoxy help

    Since you have little to lose at this point, I'd try heating the glasses with a heat gun. At temps not too far above 100F the epoxy will soften so that the bond will weaken. I'd use a scraper...
  24. Replies
    17
    Views
    1,235

    Re: brazing aluminum

    Oh, a tillerhead. Different story.
  25. Replies
    17
    Views
    1,235

    Re: brazing aluminum

    The loading of a rudderhead on a 26 foot keel boat may be very high. I think this is no place for aluminum brazing. Best to keep looking for a nice bronze rudderhead fitting on EBAY or buy a new...
  26. Replies
    291
    Views
    9,877

    Re: your personal protection

    My carry at all times is an extra pair of hearing aid batteries......you never know!
  27. Re: Cutting Hole in Fiberglass for Access Port: Methodology?

    A hole saw for such a large hole is going to be expensive. It will also require lots of torque. If something jams, large scale problems may ensue. Yes, I speak from experience using a 3 inch hole...
  28. Replies
    130
    Views
    3,678

    Re: A blizzard coming?

    Blizzard has starter here in Cundys Harbor. I prefer snow to forest fire, mud slide, flood, unbearable heat and torrential rain. The genny is in good order and the 28 year old Honda snowblower is...
  29. Replies
    21
    Views
    1,866

    Re: Old Depth Sounder

    If you put a wet finger the transducer face, you should feel a little tingle if the transducer is working.
  30. Replies
    22
    Views
    1,500

    Re: Sticking mainsail slides

    I had the same problem years ago and found it was due to varnish build-up on the under side of the track. I took an old bronze slide, bent it to fit the track well, sharpened the two ends and forced...
  31. Replies
    2
    Views
    901

    Re: Hamilton Marine Buoy Paint

    Lobster bouy paint does not deter growth of marine organisms. It is intended to go over vinyl surfaces.
  32. Replies
    26
    Views
    1,875

    Re: 1952 owens runabout.

    If you do shrinkwrap the boat be sure to leave the ends open to let the winter breeze blow thru and prevent further deterioration. Wrappers love to seal boats but that only encourages mould and rot....
  33. Replies
    20
    Views
    1,625

    Re: Shaping Herreshoff Teak Combings

    I managed to put the coamings in my Joel White 23 without a joint. The cost of teak made me switch to mahogany. I had the plank resawed, installed the outer piece and then epoxied the inner one. . ...
  34. Replies
    7
    Views
    898

    Re: Lashing one spar to another

    google square lashing
  35. Re: Reliable/bombproof centreboard pin construction. Graphalloy-bronze?

    My board is wood. Red brass is widely used for pipe in marine service as it is very resistant to salt water corrosion.
  36. Replies
    6
    Views
    863

    Re: Shop humidity with a space heater

    An electric heater in the shop will LOWER humidity levels, the extent of lowering depending on the temperature. In my experience with epoxy strip construction, heating to 60F caused no problem...
  37. Re: Reliable/bombproof centreboard pin construction. Graphalloy-bronze?

    For my Joel White 23, I used a 3/4 inch titanium pin from eBay. It rides in a red brass bushing in the 150 pound board. After three years there is no detectable corrosion on pin or bushing. The eBay...
  38. Replies
    5
    Views
    1,074

    Re: G-Flex smell and precautions?

    I've used G-Flex and never noticed greasiness. It does smell differently though.
    Dave
  39. Re: using fairing compound with epoxy below waterline

    IMHO, yes because the fairing compound I use is composed of very tiny hollow spheres. For a really smooth finish, epoxy over the sanded fairing material is necessary.
  40. Re: Oh, guess I was doing it wrong! (Card scrapers)

    Push rods from V-8 engines are incredibly hard and long enough to get a good grip on and smooth as a smelt. Most engine rebuild outfits will be happy to get rid of a few.
  41. Replies
    39
    Views
    3,318

    Re: Curly Maple

    I'm in the middle of a furniture curly maple project and have found it very difficult to machine without tearout. I finally had the panels put through a panel sander. Tear out really depends on the...
  42. Re: Need help estimating weight for transport

    My stab at it is two tons. She is only 24 feet!
  43. Replies
    6
    Views
    507

    Paddle for auxillary power

    I'm contemplating making a canoe type paddle for my 23 foot one ton sailboat. Knowing nothing about paddles, is there a preferred design for paddling a relatively heavy boat (compared to a canoe) or...
  44. Replies
    36
    Views
    4,647

    Re: Strip planking screw up...advice sought

    Excellent, glad to see you are on the right track.
    Dave
  45. Replies
    36
    Views
    4,647

    Re: Strip planking screw up...advice sought

    You have my sympathy, this is a nice design and you are doing a great job. I believe that the problem is edge set. Here is what I would do after building five boats including one strip and one cold...
  46. Replies
    9
    Views
    1,146

    Re: Help with an annoyance...

    Sawdust works on small leaks; preferably dry softwood like pine or cedar from the table saw. Dump a coffee can full on the water and stir vigorously with an oar. All you need is one or two pieces...
  47. Replies
    18
    Views
    1,405

    Re: Cutting thread in bronze rod

    sandpaper is your friend, wrap the rod to increase friction in the vise.
  48. Replies
    14
    Views
    2,509

    Re: Bow shed for storage

    The snow that slides off the bow roof can exert high side loads on the structure. If I built one, I'd make sure there was room to run the snowblower down beside the shed. Just sayin
  49. Replies
    60
    Views
    5,178

    Re: Your first real tool?

    I grew up with my father's shop full of tools but in 1961, bought a four inch Union Tool Co. double square. I still use it everytime I'm in the shop. It cost $6; Union is out of business but Brown...
  50. Replies
    10
    Views
    1,121

    Re: new outboard installation

    I was able to buy a 40 hp Yamaha and install it myself by promising to not start the engine until their tech showed up and approved the installation. It helped to invoke the time his daughter went...
Results 1 to 50 of 703
Page 1 of 15 1 2 3 4