PDA

View Full Version : Source of four-quarter 1x8 cypress (1/4 sawn pref)



Ed Harrow
03-17-2001, 09:41 PM
Sis is needing some cypress for her old house, any suggestions of possible sources?

Thanks, Ed

Ed Harrow
03-17-2001, 09:41 PM
Sis is needing some cypress for her old house, any suggestions of possible sources?

Thanks, Ed

Ed Harrow
03-17-2001, 09:41 PM
Sis is needing some cypress for her old house, any suggestions of possible sources?

Thanks, Ed

abe
03-18-2001, 06:25 AM
Ed, check out the link below. They offer Pacific coast and southern cypress.

http://www.goosebaylumber.com/CamCedCypAll.htm

They are located about an hours drive north of the Mass line.

abe
03-18-2001, 06:25 AM
Ed, check out the link below. They offer Pacific coast and southern cypress.

http://www.goosebaylumber.com/CamCedCypAll.htm

They are located about an hours drive north of the Mass line.

abe
03-18-2001, 06:25 AM
Ed, check out the link below. They offer Pacific coast and southern cypress.

http://www.goosebaylumber.com/CamCedCypAll.htm

They are located about an hours drive north of the Mass line.

Thad
03-18-2001, 06:56 AM
Ed, I have got it years past from Downs and Reader in Stoughton, then again you could always get Barber Lumber to send you some from Florida.

Thad
03-18-2001, 06:56 AM
Ed, I have got it years past from Downs and Reader in Stoughton, then again you could always get Barber Lumber to send you some from Florida.

Thad
03-18-2001, 06:56 AM
Ed, I have got it years past from Downs and Reader in Stoughton, then again you could always get Barber Lumber to send you some from Florida.

abe
03-18-2001, 07:12 AM
I am still looking for a supplier of northern white cedar for planking up a dory. Most available stock is kiln dried and OK for strip canoes, garden benches and fence posts. Guess we don't have anymore trees of sufficient size to harvest in the Northeast.

Maybe it is time to bite the bullet, forget traditional construction and use %&#*&%@ plywood. Any thoughts?

abe

abe
03-18-2001, 07:12 AM
I am still looking for a supplier of northern white cedar for planking up a dory. Most available stock is kiln dried and OK for strip canoes, garden benches and fence posts. Guess we don't have anymore trees of sufficient size to harvest in the Northeast.

Maybe it is time to bite the bullet, forget traditional construction and use %&#*&%@ plywood. Any thoughts?

abe

abe
03-18-2001, 07:12 AM
I am still looking for a supplier of northern white cedar for planking up a dory. Most available stock is kiln dried and OK for strip canoes, garden benches and fence posts. Guess we don't have anymore trees of sufficient size to harvest in the Northeast.

Maybe it is time to bite the bullet, forget traditional construction and use %&#*&%@ plywood. Any thoughts?

abe

Thad
03-18-2001, 08:22 AM
abe, talk to Dennis Day at 207-772-4465

Thad
03-18-2001, 08:22 AM
abe, talk to Dennis Day at 207-772-4465

Thad
03-18-2001, 08:22 AM
abe, talk to Dennis Day at 207-772-4465

Frank Wentzel
03-18-2001, 06:00 PM
Barbar is probably your best bet. There are numerous small mills that cut cypress here in Florida (and sell rough cut cypress for less than a dollar a board foot!) but none that I know of are set up to ship lumber.

Frank Wentzel
03-18-2001, 06:00 PM
Barbar is probably your best bet. There are numerous small mills that cut cypress here in Florida (and sell rough cut cypress for less than a dollar a board foot!) but none that I know of are set up to ship lumber.

Frank Wentzel
03-18-2001, 06:00 PM
Barbar is probably your best bet. There are numerous small mills that cut cypress here in Florida (and sell rough cut cypress for less than a dollar a board foot!) but none that I know of are set up to ship lumber.

BillP
03-18-2001, 08:35 PM
Try Kempfer Sawmill in Deer Park, Florida. 407-892-2955. They are in the heart of the cypress swamps down here and do a lot of cypress...tell how you want it and they cut it.

Bill P. in Fl.

BillP
03-18-2001, 08:35 PM
Try Kempfer Sawmill in Deer Park, Florida. 407-892-2955. They are in the heart of the cypress swamps down here and do a lot of cypress...tell how you want it and they cut it.

Bill P. in Fl.

BillP
03-18-2001, 08:35 PM
Try Kempfer Sawmill in Deer Park, Florida. 407-892-2955. They are in the heart of the cypress swamps down here and do a lot of cypress...tell how you want it and they cut it.

Bill P. in Fl.

Ed Harrow
03-19-2001, 12:13 PM
Hey, thanks all. There ought to be somebody here that will work out. Stoughton (if MA) is close by to her. Ed

Ed Harrow
03-19-2001, 12:13 PM
Hey, thanks all. There ought to be somebody here that will work out. Stoughton (if MA) is close by to her. Ed

Ed Harrow
03-19-2001, 12:13 PM
Hey, thanks all. There ought to be somebody here that will work out. Stoughton (if MA) is close by to her. Ed