View Full Version : How About a Woodenboat Models Section?

John A. Campbell
04-14-2012, 12:34 PM
I have been building wooden boat models for over 54 years and I credit that fact for my long time interest in the full size craft including some of the techniques used in the construction of them. To my knowledge there is no longer a regular publication covering boat models in this country today so what would be the chances of adding this to our favorite Publication? I feel quite strongly it would provide good incentive toward progressing to full size craft when one considers the fact that construction techniques are quite similiar.......especially in fairly large scale such as 1/4. Would like to hear from others on this. You might want to look at some of my "stuff" on www.vvm.com/~btbldr ............thanks!


Bob Cleek
04-14-2012, 01:41 PM
Great minds think alike! I was just thinking the same thing the other day. Here in the forum, there seems to be a lot of interest in modeling as well as in full sized boatbuilding. WB magazine has had a few articles in the past about ship modeling, just a few, and I think they were well received. I don't think they can really get so far afield as to devote a ton of space to models, but I do think a page or two in each issue as a regular feature would be welcomed by all. As we all age, and reality sets in, we face the fact that we can never build our "dream boats" (always more than one!) and a lot of us take to model building as the "methadone" for our wooden boat addiction. It's great fun to build a design we love "dockyard style" just as the full sized vessel would be built, and a lot easier on old backs and pocketbooks. Having built models on and off all my life, I am convinced that one has a very difficult time building a good model if they don't have a complete grasp of how the full sized vessel is really constructed.

04-14-2012, 03:08 PM
beautiful work John! very inspiring. i think it's a great idea. Bob has summed it up very well (as usual). it is a great way to feed the addiction. as someone who has only recently started modeling wooden boats, i would love a place to find more ideas and information.


wizbang 13
04-14-2012, 04:35 PM
http://farm8.staticflickr.com/7272/6931701360_96cd372af8_z_d.jpgI am very proud of this one!

04-14-2012, 10:42 PM
I liked the models covered in Currents in issue 225 and would be happy to see a page or two covering ship models and modeling on a regular basis.

Rich Jones
04-15-2012, 07:06 AM
It would be nice to see a few more articles on this. My whole life, I've been building full size boats as a hobby. Physicial limitations are now slowing me down a bit (although I still have at least one full time build left in me!) and I'm thinking more and more of modeling. I would like to build an RC sailboat that looks like the real thing, not just the hobby-store designs.

04-15-2012, 11:22 AM
The "Footy effort" of a few years ago was one that I hoped would take off as a way for modelers to get a toehold here on the Forum and at the Show and perhaps at the School (which has expanded its modeling classes in a different direction).

I was sad to see it fizzle.

John A. Campbell
04-15-2012, 12:31 PM
Many thanks for the fine response.....I think one of the key elements in model boat building is the satisfaction one gets from lofting a boat at a scale of anywhere from 1/8 to 1/4 ......I use 8X8 or 10X10 to the inch grid fadeout velum available at any blueprint shop which is a great aid in assuring accuracy of the overall project. Most scales are available on standard triangular architect's rules however if one desires a special scale, contact The Scale Card, P.O. Box 2872, Crestline, CA 92325-2872 or www.thescalecard.com and they'll make you a plasticized scale card at whatever scale you wish at nominal cost. I used 2.5"=1'0" on my live steam launch and plan to use the same on a 28-foot 1929 Chris Craft Upswept triple cockpit runabout. And for drive systems, you cannot beat Rich Cole at M.A.C.K. Products Model Marine, P.O. Box 464, Long Branch, NJ 07740-0464 (732-870-2966)......Rich has a full line of electric motors available in single or dual and geared in a variety of ratios plus shafts, couplings, excellent PWM speed controls, etc. and he really knows his stuff. I ordered three sets of drives from him last fall when building three 38" Hacker runabouts for one granddaughter and two grandsons for Christmas. Also....for a source of top quality Finnish Birch aircraft plywood, most hobby shops can supply this but I would suggest Aircraft Spruce West in Corona CA (800-824-1930) or their eastern division Aircraft Spruce East in Griffin, GA (800-831-2949).....they have it in 7 thicknesses from .4 mm up to 6 mm and in 50" X 50" sheets and it will be considerably cheaper and there will be more USEABLE (less waste) material in the long run than buying from hobby or craft stores. I really like using the .8 mm as underlayment for models planked in 1/16" Honduran mahogany, cedar, etc. and the 1.5 mm for thicker planking.

I feel strongly that if one plans to build a really nice model, he should consider building at a fairly large scale.....never anything smaller than 1/8.... and preferably 1/6 , 1/4, or a bit larger if his shop space and, more importantly, his method of transporting the model to the water's edge will allow it. The cost difference between a 1/8 scale model and a 1/6 or 1/4 scale model is not very significant and if one plans to install radio control equipment, the larger model will be much more realistic in operation due to wave action on the smaller model. The gear motors that Rich Cole sells have very high torque at 12 VDC and you will be rewarded by very good performance if you follow his recommendations. By the way, he also sells sail control mechanisms.

John A. Campbell
04-15-2012, 12:57 PM
In defense of building large scale models over small scale, I wanted to add that construction of the larger model is much easier as it will withstand clamping pressures much better and alignment, fastening, repairs of "mistakes" will be much easier and will be much more forgiving of handling problems at the water's edge than the smaller model........


04-18-2012, 07:17 AM
As a long term subscriber, I'd very much like to see a model section in the magazine. There are lots of people who love wooden boats, but don't have the wherewithal to build for themselves in full scale. Even for those planning to build in 12"=1' scale, it can be a great help to put a model together first. No matter how you try to represent a three dimensional object on paper, or on a computer screen, nothing can compare with having an actual object that you can look at, that you can run your hands over -- there is no real substitute for that.

Here's a couple of shots of the model I am building of a boat I've designed and would like to build full size.




John A. Campbell
04-18-2012, 05:21 PM
She's gonna be a beauty....no doubt about that!

Another interesting facet in the building of models is the construction of deck and cockpit hardware. I build my hardware to scale using purple jeweler's wax ....the blue is too soft and the green is too hard and brittle.......purple carves just right. Then I take the pieces to a nearby custom jeweler and he casts them for me in brass (or silver if needed) using the lost wax process. After casting, I polish the rough castings and give them back to him to make wax injection molds in Castanaldo rubber for future hardware items. The detail that is obtained using lost wax casting is amazing.....I've even seen a fingerprint show up on a piece.......I've toyed with doing my own casting but haven't quite made that move yet.

Realizing that one cannot take a ride in one of his models, if his "Number 1 Pleasure" in wooden boats is the planning, construction, and finishing of them, then I think models are a wonderful way to experience this at far less cost and with a wide open field with regard to the number and type one could build and store during his lifetime. I still have an old 42" wooden hydroplane (an Octura White Heat 460 "kit boat") that was radio controlled and powered with a .56 cubic inch Supertiger engine and this boat was built in the '60's.


04-18-2012, 10:33 PM
Amen to the model section. I would definitely participate. Here's a model mackinaw that I started as a study for the real-deal. I planked 1/2 traditionally and the other 1/2 using strips to see how the planks would run.1884

Paul Montgomery
04-18-2012, 11:48 PM
A model section makes sense. I just finished one but haven't photographed it yet. Here's one I built before tho:



04-19-2012, 03:50 PM
Nice job Paul. Have you considered skinning it with something clear, like saran wrap?

04-19-2012, 03:58 PM
Here's my version of a melonseed I did years ago.

04-19-2012, 04:29 PM
Hey John, quit fooling around with the models and get that Victor Slocum wet!

Paul Montgomery
04-19-2012, 07:40 PM
Nice job Paul. Have you considered skinning it with something clear, like saran wrap?

I have but I don't think I would be able to do it well enough. I've also thought of paper. It would have to be able to show the frame well tho.

John A. Campbell
04-19-2012, 09:08 PM
Paul, wonder how applying really sheer ladies hose would work as a skinning material? No doubt the frames would show through and the covering would be strong however if you tried to apply a clear lacquer over it, it might tighten up and damage the model......I believe I would try it on a scrap assembly of some sort to see how it would look & work.

Also.......Kbowen, Paul, and Chrisben.....you've got some really beautiful work there !

Also....Denny, the instrument panel & 1/4" adjustable stainless steel motor mount is complete.....progress is being made! ....Victor Slocum is my SwanSong for full size craft

I have but I don't think I would be able to do it well enough. I've also thought of paper. It would have to be able to show the frame well tho.

John A. Campbell
04-19-2012, 09:13 PM
Paul, another thought in favor of sheer ladies hose.....I think the covering needs to have the slight bit of color (very light tan) that this would provide....if you used something completely water clear, I don't think you would get the appearance that the model needs.....you need to somehow delicately accent that covering......just my 2 cents worth.
I have but I don't think I would be able to do it well enough. I've also thought of paper. It would have to be able to show the frame well tho.

Paul Montgomery
04-19-2012, 09:25 PM
Paul, wonder how applying really sheer ladies hose would work as a skinning material?

Good idea. I might have to try that.

04-20-2012, 05:59 AM
I've built a lot of Sterling mahogany Chris-craft kits...but can't find the pictures...
So here's a (gasp!) PLASTIC Flower Class Corvette I put together over the winter...

And for those who do not know, I am the owner of Easytiger Models.
And we are rather seriously into manufacturing giant sized RC model aircraft, particularly electric power, check it out at www.easytigermodels.com or http://www.youtube.com/user/easytigermodels?feature=mhee
It may open your eyes a little bit as to what is out there today....

Bob Cleek
04-20-2012, 04:08 PM
And for those who do not know, I am the owner of Easytiger Models.
And we are rather seriously into manufacturing giant sized RC model aircraft, particularly electric power, check it out at www.easytigermodels.com or http://www.youtube.com/user/easytigermodels?feature=mhee
It may open your eyes a little bit as to what is out there today....

Wow! I've crashed more than my share of control line model airplanes back in my youth. Taking a nosedive with one of your model planes would be a costly mishap! Do you have to clear flying those with the FAA? Scary, but neat!

04-23-2012, 07:51 AM
How about a list of model boatbuilding clubs, i would like to start a club even though i am not a model builder. Maybe i could learn to build something half as beautiful as the ones you build. Anyone who is interested in starting a club can give me a call,631-225-1666 we can meet at my shop Long Island N.Y.

Paul Montgomery
04-29-2012, 10:22 PM
I just finished my latest - a Greenland kayak:


Other models:



04-30-2012, 03:50 AM
This thread has prompted me to get a damaged model Barque out of it's box and begin repairs. She dates from about the 1940's and was made by an Italian prisoner of war from a piece of pine and old wooden fruit boxes mostly. Not bad, made without too many references probably but historic because of it's origins. Somewhere along the way she was dropped, badly but all the bits were kept and I acquired her about 20 years ago. Never quite got round to restoration till now, never quite felt I could do it justice but I've started.

05-01-2012, 07:00 AM
I know that in order to get real usable data from a model it should be large (say 6' at least) and used under exacting and controlled conditions. But I think there are some things that can be learned even from smaller, less sophisticated model testing.

Realistic drag figures? Probably not -- but floatation, steerage, and wake formation -- maybe so...

Here's a two minute clip of my "Atkin-ised" raised deck cruiser. Trimming well at a scale 7300#, turning and maneuvering, and running at scale speed with very little wake.



John A. Campbell
05-01-2012, 05:01 PM
Very, very nice model with excellent running characteristics......a quality model indeed.

And, Walterc, there are RC boat clubs in many places (at least 4 in Texas) but they are racing clubs with (gasp!) f--------s hulls. I don't know of any that are dedicated to wooden hulls, scale or otherwise. Once upon a time I started to build a model of John Hacker's "My Sweetie", a step hydroplane from the late '40's and early '50's....a gorgeous boat it was....and when I contacted one of the clubs (Dallas) and told them what I was planning and that I wanted to install a 22 cc Zenoah w/centrifugal clutch in it they wouldn't allow it ....that was years ago....I doubt if they've changed their mind.

The VERY BEST model boat club in the USA (in my opinion) is the San Francisco Model Yacht Club........ they've got everything....beautiful scale, gas, electric, steam....I was there in 1998 for their Centennial event (yep, they've been organized since 1898) and I ain't never gonna forget that experience....they've got their own pond very near downtown San Francisco that was donated by a very wealthy fellow who was in the big-time sugar business....his name escapes me at the moment.....the club's President in 1998 was Ken Valk.

Bob Cleek, you are a lucky man.....you're right there in San Francisco.....you ought to be right in the midst of them all the time!


05-01-2012, 05:35 PM
I would be interested in a forum like this because my experience with the two local (Chicago) RC sail clubs is that they are all about racing. I went to their gatherings for a while and someone might bring a unique project they were working on and everyone would gather around for about 10 minutes and then it would sit on the bank while they got back to racing the class-du-jour: Soling 1 meter, or Santa Barbara, or 12's. I scratch-built a Friendship sloop which I brought to the lake a couple times and everyone referred to it as "the schooner" presumably because it was Gaff-rigged. It was often an "almost-fun" experience.

05-01-2012, 06:30 PM
When I was a kid I was fascinated with anything that would float and progressed through various degrees of toy and pond yachts till my models were 6ft long topsail schooners with a the basic RC available at the time. When one sailed out of range and was lost the next boat I built was a chase boat, a canoe, out of plywood and that's where it all started.

05-02-2012, 10:12 AM
I just finished my latest - a Greenland kayak:


Other models:



Very nice! What scale are these kayaks done at? What materials used?


Paul Montgomery
05-02-2012, 07:15 PM
Very nice! What scale are these kayaks done at? What materials used?


Thanks. The are 1:4 scale. The Greenland is all Alaskan Yellow Cedar. The baidarka is Western Red Cedar, Oak and bamboo skerwers for the ribs (but I won't make THAT mistake again!).

05-03-2012, 11:25 AM
Thanks. The are 1:4 scale. The Greenland is all Alaskan Yellow Cedar. The baidarka is Western Red Cedar, Oak and bamboo skerwers for the ribs (but I won't make THAT mistake again!).

1:4 scale? That would make it about four feet long, maybe? If I read that correctly. Never thought to work that large with models. I've only made a few rough looking ones at an inch equals a foot. Mostly to figure out construction for the full sized boat. Not small, as a finished art piece, itself.

I might try my hand at some skin-on-frame models in the near future. Building a full sized one in my garage (Dave Gentry Chuckanut 12) has piqued my interest in more traditional designs.


Paul Montgomery
05-03-2012, 05:13 PM
1:4 scale? That would make it about four feet long, maybe? If I read that correctly. Never thought to work that large with models.

Yep. Adney did 1:5 but I find it easier to work out scale in inches by going 1:4. Any smaller and I'm afraid the detail would be lost. 1:2 scale would be a fun size to make a RC boat :-)

mick allen
05-04-2012, 01:30 AM
Paul Montgomery wrote
I have but I don't think I would be able to do it well enough. I've also thought of paper. It would have to be able to show the frame well tho.

Great skins for SOF kayak models are model airplane iron-ons:
1)fabric (it's a real fine fabric with an iron-on coating) for a great SOF nylon/polyester skin simulation. Shrinks all you could want and will take about 10 minutes to cover that model. Real fast, you'll just love what you can do with it.
2)Or one of the plastic iron-on films - they can be opaque, to translucent, to transparent - just check your local rc airplane outlet.

Michael Wick
07-08-2012, 04:17 PM
In the website www.traditionalsmallcraft.com (http://www.traditionalsmallcraft.com), we have been writing about building models before and as we build the real boats. would love to hanve some pictures and copy of other models. Especially ChrisBen's beautiful melonseed model.

Peerie Maa
07-08-2012, 05:14 PM
At the close of the Coble build thread I mentioned the need to build a stand for her. Built it this week end.
Fruit woods and bone.

07-31-2012, 02:18 PM
Hello friends,

During my third attempt of the transom of my Spitsailskiff by Rogers is dried/drying I present you my first time the next planned project. It is a shallow-draft boat with a V-shaped bottom, a sprit & foresail and centerboard.

As a boat needs a name so I'm unimaginative as it is named after Howard I. Chapelles residence in Maryland: CAMBRIDGE. (The alternative to baptize them after the place of construction Miracle I was given the uncertain end of this building bit exaggerated.)

http://www.bilder-hochladen.net/files/thumbs/ag4q-1j-a684.jpg (http://www.bilder-hochladen.net/files/ag4q-1j-a684-jpg.html)
Here my slipway - besides the Steve Rogers book "The Spritsail Skiff"- construction I work on Camebridge. So you can see that I am forced to take down it from time to time when the livingroom table is needed for visitors ect. The flower on the tableis a present of my wife. Right beside the Capelle - >Boat Building< my pocket plane, on the cutting mat the cut out mold-stencils - held together by a clothespeg. In the left top corner the stapler for my project DIN A4 copies.

The plan comes from his book "Boatbuilding" and is to find on the Plates 39, 40 and 41 (what saves me of the editiondepending page numbers). This is not a modelshipbuildingplan!! The documents come from a book for the amateur boat building of the 50th and the plan is actually intended to build such a boat in 1'= 12" and the hole plan consists of three pages:

http://www.bilder-hochladen.net/files/thumbs/ag4q-1c-67c6.jpg (http://www.bilder-hochladen.net/files/ag4q-1c-67c6-jpg.html)
a) a very elaborate Sailsplan in a WL-side view

http://www.bilder-hochladen.net/files/thumbs/ag4q-1d-642e.jpg (http://www.bilder-hochladen.net/files/ag4q-1d-642e-jpg.html)

b) the necessary linesplan

http://www.bilder-hochladen.net/files/thumbs/ag4q-1e-f457.jpg (http://www.bilder-hochladen.net/files/ag4q-1e-f457-jpg.html)
c) a fantastic wood plan.

In the latter in twenty-five positions are known in detail. The built-in timber types (and their alternatives) and their exact dimensions - to be joined by a number of sectional drawings and specifications required by the metal components.

Chapelle attached great importance to acuratesse and delivered his plans often with enlargement of the stem and rudder sheets - here a scale of 1 1/2 "= 1ft 0inch is given and often a 6x6 inch grid was placed over it - here it is 3x6" instead. The essential messament points in feet, inches and eighths indicate that one can control his body plan it are given in an extra spreadsheet.
Also detailed are the dimensions of the rigging in sailsplan advantage.

Here, first the inscription:

Double-ended skiff skrabbing,
Called a "sharpie", probably built
at "Miracle" Hopkins Iceland, 1926

From this drawing, the dimensions measured on 21st April 1941, my 3 plan sheets seem to arise.
As you see, I am very careful, the similarities are there, but real security to a firm assertion that so I have not (yet).

Meanwhile I coloured the Woodplan to identify the diffrend types of wood by colour - nicely colourfull. :d
I recoginzed that the hole formerplan was bent - it was an arc instead of a chord!
So I was told - "That is the usually way it is!" - and I remembered somebody named Murphy. And I felt like an complet idiot!!!

...and so I began to redraw the hole formers plan in 2:1 (or scaled 1:6).
And it got well!

Than I took the thickness of the side and bottom planking and put this measurement (nearly 3.2mm) in a calliper and then a small pair of compasses. By using this way I reduced the "bulkheads" down to the measurement I neet in the building jig.

Now I can show the drawings to you my scibblings and give you an idea of the work I did today. Todays work will be ready when I copied them (back to scale) down to the half of the drawn size.

Hopefully I am able to copie the 1:12 jig lines today cutting them out and glue them onto the 6mm beech plywood, too.

Now the fist problem appear:

The distance in high between chine and top of coaming differs between longitudinal drawing in the woodplan and the former detail cutaways!
Am I right to belief in my frames in the plan and use this and the rest will be results?

http://www.bilder-hochladen.net/files/thumbs/ag4q-1f-c0c7.jpg (http://www.bilder-hochladen.net/files/ag4q-1f-c0c7-jpg.html)
...and something positiv - the jig/molde drawings, a ruler half-mm and 1 €cent.

It is not a very large step foreward - but I got the Russian Larch I need to imitate Oak on pices like stern or stem and so on. (It was not easy [or cheap] to get such a little dimensions - in Germany Russian Larch is mainly used for building terace. So you can mostly order a completly laden lorry trailer or a single plank of four yards minimum. Mainly fluted as floor... or in shorter dimensions the appear allways cut and screwed together as a wooden tile for use as garden cheese platter.)

The moldplan will be in the next weeks altered again - I got the tip from a older college to plane the bottom sides 0.3mm down to add a 0.3mm pice of plywood. This to be able to build a realistic, flat and even bottom. This to get the bottom planking underpinned on every sixty-fourth squareinch by a masked pice of plywood.

And a view over my shoulder on my 2 model working table in the livingroom - on it a inner coated panel of a old wall unit - cramped to the dining table by the vice and the lamps base. In the front left corner the jig of my spritsail skiff in the vice. Behind the cutting mat a little pile of wood for the fixing of the molds - untailored. Beside a glas of wather and a old make-up brush to take away the well forth wood-glue.

Greetings from the Spree-Athen sends you,

„If god gave trees the admirable forbearance to grow; we will have the time to build with patience."

On the slipway:
a) H.I. Chapelle (Boatbuilding Plates 39-41): "Cambrige" 1'=1'' 20ft Sharpie

In work scheduling:
a) Russel Barnes (MSW):"Romeo y Julieta" Biloxi Oyster Skiff
b) H.I. Chapelle (BOAT Magazine, 1956):"Montecristo" 14' 1/4'' Sharpie skiff

08-11-2012, 07:45 AM
Here the latest news about my "Cambridge":
The softwood block is to keep the bottom's planking in order I thought about rc-flying plywood but it was so expensive that I changed my mind. The block will be beveled to the right measurement.





As I"ll need 254 years to build a 1'=12" I ask for a seperated part for the modelshipbuilders in here.
What do you think?

Hope you enjoy it.

wizbang 13
08-11-2012, 11:39 AM
https://sphotos-b.xx.fbcdn.net/hphotos-snc7/576830_431672220177055_1072958742_n.jpghttps://sphotos-a.xx.fbcdn.net/hphotos-snc7/380353_431671390177138_55478589_n.jpgooh ooh , found some old pics of a model I built in about 1979, geeze I mizz that dog.

09-10-2012, 12:25 PM
I just give this thread a little bump.

And a question, (sorry I don't know how to insert a poll)

So the question is:

I want to build a model boat for my main sponsors.

First I was smitten by a 24' Hampden boat by Howard Chapelle, being one of the last (IMHO) boats without an engine.

On consulting some friends they all advised me to build a model of the 25'outboard cruiser I am actually building.

Please let me know what you think :confused:

Gerrit Jan

wizbang 13
09-10-2012, 02:15 PM

09-12-2012, 12:35 PM


The reasoning of my friends was that the 25' outboarder would be truly a thing of myself. Cannot find fault with this reasoning, and I start liking the idea.

But I will most surely build the Hampden boat, would be a great fun expierience to build it.

Busy weekends lay ahead.

09-14-2012, 01:38 PM
First I will start the model fo the 25 footer I am building.

It will give me some insight in how the boat will look.

Now did the model boat building bug bite me or can I just scratch it off :confused:

Antonio Majer
09-15-2012, 02:15 PM
I, too, have built some rough study-models before trying to actually build the boat.


The first is the famous dark harbor 12' I never started building; then a Whitehall, a dinghy 12' and a peapod (the only model of mine with its real counterpart (https://picasaweb.google.com/115462673884116271339/PeapodLanciaAmericanaBacelloDeiPiselli#57375893301 27599042) )

Here the dinghy I'm currently building



...and its would-be keel


John A. Campbell
09-18-2012, 01:08 PM
Beautiful work, Antonio......absolutely stunning.

09-26-2012, 02:25 PM
I received the DNGoodchild plans for Howars Chapelle's Glouster schooner, as soon as I have finished the model of the boat I am actually building (a 25'outboard cruiser), I will start building a nice large scale model of that.

10-11-2012, 01:25 PM
I like the idea of this thread. I can't contribute a whole lot but there are two models I have built over the years that I'll toss in here. The first one I built off the plans for "Snarlyow" from Mystic Seport. The real boat is about a 15' cat-cutter hull for which the seaport has no rig. I built her as a hollowed out liftslab constructied hull and then scaled the rig off "Fox"/"Galina" (also in the seaport's collection). Shee was intended to be a sailing pond model, but I couldn't get the internal balast low enought. She floats basically on her lines, but lists quite a bit at rest from the weight of her rig.

vhttp://im1.shutterfly.com/media/47a2ce31b3127ccef101f69b3fda00000040O12Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D1/rx%3D550/ry%3D400/

http://im1.shutterfly.com/media/47a2ce31b3127ccef100c7475fca00000040O12Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D1/rx%3D550/ry%3D400/
http://im1.shutterfly.com/media/47a2ce31b3127ccef1009bc35f6000000030O02Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

http://im1.shutterfly.com/media/47a2ce31b3127ccef10096171f2a00000030O02Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

http://im1.shutterfly.com/media/47a2ce31b3127ccef10091e45f4200000030O02Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

http://im1.shutterfly.com/media/47a2ce31b3127ccef10081e7de7900000030O02Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

10-11-2012, 01:40 PM
This Whitehall was also built off of plans from Mystic Seaport (for a 15' traditional carvel planked Whitehall).

http://im1.shutterfly.com/media/47a2ce31b3127ccef1009131dea700000040O12Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D1/rx%3D550/ry%3D400/

http://im1.shutterfly.com/media/47a2ce31b3127ccef1009aa49eaf00000030O02Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

http://im1.shutterfly.com/media/47a2ce31b3127ccef10029f5de3f00000030O02Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

http://im1.shutterfly.com/media/47a2ce31b3127ccef10188c7be8900000030O02Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

http://im1.shutterfly.com/media/47a2ce31b3127ccef10124483f6000000030O02Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

http://im1.shutterfly.com/media/47a2ce31b3127ccef101a6c8be9100000030O02Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

10-11-2012, 01:44 PM
http://im1.shutterfly.com/media/47a2ce31b3127ccef100e29f1f9800000030O02Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

http://im1.shutterfly.com/media/47a2ce31b3127ccef1010a073f3800000030O02Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

http://im1.shutterfly.com/media/47a2ce31b3127ccef100703f9e4100000030O02Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

http://im1.shutterfly.com/media/47a2ce31b3127ccef1003ae71f8c00000030O02Bbs3DVuzZA9 vPhI/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

Let's see some other's.

Peerie Maa
10-11-2012, 03:46 PM
Hi nedl
I can see how you had a problem with the pond yacht. You always have to deepen the keel and hang the ballast underneath because although displacement scaled by the cube of length, stability scales by the fourth power.
My offering is #36, from here:http://forum.woodenboat.com/showthread.php?149296-Building-a-coble

10-11-2012, 09:59 PM
Nick, I don't know how I missed your building a coble thread in June. Just beautiful the way you built her!
My cutter model floated beautifully, ..... before I rigged her.

J. Dillon
10-12-2012, 11:45 AM
Great work here, lets see more please.

10-12-2012, 11:55 AM
Jack - I know we've seen your work before (just beautiful!), but you should post some of it here also.

10-14-2012, 05:35 PM
Nice to see some other ship modelers about. I've just started a pinky schooner model earlier this year, still in bones till I get to it again between other (full-size) boat projects: